How to Reset Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648?

To everyone who required resetter for canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 to reset ink counter on these canon printer model, I found how to reset these canon printers model on indoreset. Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 is canon all in one printer verison that designed for home and small office.

I don’t know this reset method work or not on canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 because I don’t have this printer model to try this reset method.

Ready to reset your printer, follow the following steps:

All these steps must be done to reset your canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 printer.

A. Entering into service mode

• Turn off the printer off is the printer power on. And remove the printer USB cable from your computer..
• While the printer is OFF, press and hold the Start/Stop button on the some other canon printers model press Resume/Cancel button.
• While still holding Start/Stop button or Resume/Cancel button, press and hold the POWER button.
• When the POWER LED (green light) lit, release the Start/Stop or resume/cancel button (still holding the POWER button).
• Still holding the power button,   Press the Start/Stop button or resume/cancel button TWICE then Release the POWER button. Wait until LCD printer to display 0 (zero) number
• After the display is 0, attach the printer UDB cable to your computer, its will detected new device installed (its normal), now go to resetting steps

B. Resetting Ink counter on the Printer

• Run “service_tool 1050.exe”. you can download the service tool software from this link: ServiceTool_1050.zip
  

• Confirm detected USB-port numbers on USB port column.
• Click “Main button” on Clear ink counter section. Make sure there are papers in the paper feed because the printer will print after the process is complete.
• Click “platen button” on the “Clear ink counter” section. The printer will print again.
• Turn off the printer and then turn the printer on. You printer is ready for use.

If you have any problems just comment. 

Don't forget to thanks.... :-)

Powered By: http://sunssolution.blogspot.com/

How to put background picture in your USB?

You can actually customize the background of your USB flash drive by following this simple steps. :)

Step 1:

Copy this code to your text editor or notepad,then save it as "desktop.ini"

Code:
[.ShellClassInfo]
IconFile=%SystemRoot%\system32\SHELL32.dll
IconIndex=127
ConfirmFileOp=0

[{BE098140-A513-11D0-A3A4-00C04FD706EC}]
Attributes=1
IconArea_Image="your_picture.jpg"
IconArea_Text="0xFFFFFF"
VeBRA sources - don't delete the tag above, it's there for XXXXX purposes -
[ExtShellFolderViews]
{BE098140-A513-11D0-A3A4-00C04FD706EC}={BE098140-A513-11D0-A3A4-00C04FD706EC}
{5984FFE0-28D4-11CF-AE66-08002B2E1262}={5984FFE0-28D4-11CF-AE66-08002B2E1262}

[{5984FFE0-28D4-11CF-AE66-08002B2E1262}]
PersistMoniker=Folder.htt
PersistMonikerPreview=%WebDir%\folder.bmp

Step 2:
Put "desktop.ini and your_picture.jpg in ur USB Drive then Hide it if you want.

Step3:
Refresh or re-insert your USB flash drive..and enjoy with new background...

If you have any problems just comment. 

Don't forget to thanks.... :-)

Powered By: http://sunssolution.blogspot.com/

How to change your USB Flash Drive Icon?

Done with Windows XP but should work on All Windows Versions

1.Go to Notepad(Start --> All Programs --> Accessories --> Notepad).

2. Type the Following:
     Code : [Select]
------------------------------------------------------------------------------------------------------------------------------------------------------------------
     [Autorun]
     icon = youricon.ico
------------------------------------------------------------------------------------------------------------------------------------------------------------------
Where youricon.ico is the name of the icon file

3.Go to File  --> Save As --> Name it autorun.inf and save it in the Root of the USB Drive.(For     
   me it's F:\)

4.Now all you need is an Icon. Icons can be downloaded off the internet but if you habe a picture  
   you want to convert into an Icon(.ico), there are plenty of programs to do so.

5. When you get your Icon, move it to the Root of your USB Drive along with the Autorun file.

6. Unplug the drive and plug it back in and you should be able to see your custom icon.
    ( If unplugging the drive doesn't work, try restarting the computer) 

If you have any problems just comment. 

Don't forget to thanks.... :-)

Powered By: http://sunssolution.blogspot.com/

How to Install Ubuntu 12.10 (Quantal) LAMP Server Setup?

In around 15 minutes, the time it takes to install Ubuntu Server Edition, you can have a LAMP (Linux, Apache, MySQL and PHP) server up and ready to go. This feature, exclusive to Ubuntu Server Edition, is available at the time of installation.The LAMP option means you don’t have to install and integrate each of the four separate LAMP components, a process which can take hours and requires someone who is skilled in the installation and configuration of the individual applications. Instead, you get increased security, reduced time-to-install, and reduced risk of misconfiguration, all of which results in a lower cost of ownership.Currently this installation provide PostgreSQL database, Mail Server, Open SSH Server,Samba File Server, Print Server, Tomcat Java Server,Virtual Machine Host,Manual Package selection,LAMP and DNS options for pre-configured installations, easing the deployment of common server configurations.

Ubuntu LAMP server Install the following Versions

Ubuntu 12.10 (Quantal)
     Apache 2.2.22
     Mysql 5.5.27
     PHP 5.4.6

First you need to download server version of Ubuntu version from here after that create a CD and start booting with the CD Once it starts booting you should see the following screen in this you need to select your language and press enter.

Now you need to select “Install Ubuntu Server” and press enter

Select your language and press enter

Select your location and press enter

If you want to try to have your keyboard layout detected by pressing a series of keys you need to select yes option.If you want to choose from a list click no

Select Origin of keyboard and press enter

Select keyboard layout and press enter

Detecting hardware to find CD-ROM Drivers in progress

Loading additional components in progress

Configures the network with DHCP if there is a DHCP server in your network

Enter your server Hostname

You need enter the Full name of the user you want to create for your server in this example i have created ubuntu user select continue and press enter

Enter your user account name here

Entered the password for ubuntu user select continue and press enter

Confirm password for ubuntu user

If you want to configure encrypted private directory select yes otherwise no and press enter

Configuring clock option

Detecting disks and all other hardware

You have to partition your hard disk in this example i have selected use entire disk option.If you want to do manually you can choose manual option and press enter.Make sure you have swap partition in place

Warning message about data lost on your hard disk

Guided Partitioning

Write the changes to disk here you need to select yes and press enter

Creating ext4 file system in progress

Installing  system in progress

Configuring the package manager select continue and press enter

Configuring package mirror this will be related to your country option

Select and install software in progress

Select how do you want to configure automatic update press enter

Now it will start Installing software and here you need to select the server options here i have selected as openssh server and LAMP server installation.If you want to select each package separately select "Manual package selection" option

At the time of software installation it will prompt for mysql server root password enter root password of your choice and select continue

Confirm mysql server root password and select continue

Software installation is in progress

Installing GRUB Boot loader in progress

Finishing installation in Progress

Installation complete message here you need to remove your CD select continue and press enter it will reboot your server

After rebooting your server it will prompt for username and password once you logged in you should see similar to the following screen

This will complete the Ubuntu 12.10 (Quantal) LAMP Server Installation and your server is ready for installing applications which supports apache,mysql and php.

Configuring Static ip address in Ubuntu server

If you want to install vim editor use the following command

sudo apt-get install vim

Ubuntu installer has configured our system to get its network settings via DHCP, Now we will change that to a static IP address for this you need to edit

Edit /etc/network/interfaces and enter your ip address details (in this example setup I will use the IP address 172.19.0.10):

sudo vi /etc/network/interfaces

and enter the following save the file and exit (In vi, ESC, then ZZ to save and exit)

# The primary network interface

auto eth0
iface eth0 inet static
address 172.19.0.10
netmask 255.255.255.0
network 172.19.0.0
broadcast 172.19.0.255
gateway 172.19.0.1

Now you need to restart your network services using the following command

sudo /etc/init.d/networking restart

You need to setup manually DNS servers in resolv.conf file when you are not using DHCP.

sudo vi /etc/resolv.conf

You need to add look something like this
search domain.com
nameserver xxx.xxx.xxx.xxx

If you have any problems just comment. 

Don't forget to thanks.... :-)

Powered By: http://sunssolution.blogspot.com/

How to Install Ubuntu 11.10?

Step 1:
The first thing you should do is head to http://www.ubuntu.com/download/ubuntu/download and download Ubuntu 11.10 LiveCD. Just click the big orange Start download box.

Step 2:
Using your disc burning software, burn the .iso you downloaded to a CD. 

Step 3:
Before you go any further, ensure all important data is backed up in case of data loss on your drives. This guide assumes you have media backups of your Windows partitioned hard drive and you are safe to proceed.

***Warning: Installing another operating system without first ensuring you have backups of your current files and operating system is a big risk. If you have no data to lose or you’ve backed up important data, you’re ready to proceed. YOU are responsible if you lose data.For those of you using Windows, and installing Linux for the first time I recommend you either use a separate hard disk that does not contain the Windows OS, or create a partition big enough for Linux within Windows using Disk Management in the Administrative Tools menu of the control panel. 30GB of hard disk space is absolutely plenty of space for you to begin exploring Ubuntu whilst at the same time having room to grow.

Step 4:
Ensure you have a network cable connected, restart your computer, and boot from the CD drive.

Step 5:
The LiveCD will load up, and you'll be presented by the following box:



For the purposes of this guide, we will assume you've already tried Ubuntu and want to proceed with an installation, so click "Install Ubuntu."

Step 6:
You'll be greeted by the "Preparing to install Ubuntu" screen, exactly as below:



I recommend you select "Install third-party software" as I have done in the screenshot above. I prefer to do system updates once up and running, but if you have the extra time you can also select "download updates while installing" as well. Then click continue.

Step 7:
The next screen you will see is "installation type," what you see will be dependent on whether you have an existing Windows installation or not. 

I'm going to split this into three different sub-steps, to make it as simple as possible.

Step 7-A:
For those installing in a virtual machine or to hard disks without an OS you will see the following screen:



You have two choices:

1. Erase the entire disk and use all of it for installation -- Ubuntu will automatically partition your disk and proceed with installation.
2. Select "something else" and manually create your partitions (which is covered in detail in step 7-C).

If you are choosing the first option, select the radio button and then click continue, proceeding to step 8.

Step 7-B:
Those of you that have current Windows installations or are going to dual-boot with another existing OS will be presented with a screen similar to below:




You have three options available:

1. You can choose the first option and install Ubuntu alongside your existing OS. 
2. You can opt to replace your Windows installation with Ubuntu, allowing the installer to format your current partitions and automatically create new ones for Linux.
3. You can choose "something else" and create your own partition scheme and sizing (covered in detail in step 7-C).

Once you have selected which route you wish to proceed with click continue and proceed to step 8.

Step 7-C:
Having selected the "something else" option you will be presented with the following window:




Linux recognizes and assigns IDs to drive in a different manner to Windows. In the above image, you can clearly see my hard disk in the list. It is identified by "/dev/sda." Linux recognizes drives in the following way: 
• Sda = 1st drive
• Sdb = 2nd drive
• Sdc = 3rd drive and so on 

Partitions are also shown after the drive letters. So if I had 2 partitions on my first disk, they would be identified as:
• Sda1 – 1st drive, 1st partition
• Sda2 – 1st drive, 2nd partition

You will not see the common Windows C: label in the disk menu in the above list. You do, however, have key things to help you recognize your Windows C: drive. Both of these can be used to identify which is your Windows disk.
• The size of the disk is shown
• The name of the drive is shown

This is your current partition layout for your hard disks. If you have more than one disk, they will show up as /dev/sda, /dev/sdb etc.

Firstly, identify your Windows installation. In my case, it's sda1 (which is my first hard disk, first partition). What you see depends on how you created the extra space. I just resized the Windows partition from within Windows, and left the free space ready to install Linux. I recommend using Windows or a free utility from within Windows to resize your partition as most beginners will understand it more.

Therefore, we now need create a minimum of two partitions:

Click "Add" and the following box will appear:



You will notice I have already filled out the example above to create a 10GB root partition.

You can have a maximum of 4 primary partitions, or 3 primary partitions and 1 logical (which allows for another 64 partitions)
The size above is 10.00GB. e.g 1,000 = 1GB 10,000 = 10GB (Remember to leave enough free remaining space to create your SWAP partition!)
Location for new partition: e.g. do you want it at the start or end of the free space. Select beginning.
Use as: Ext4 is the recommended file system for Ubuntu, much the same as NTFS is Windows. SWAP is for SWAP space.
Mount point: This is where you want the partition to mount. E.g. we need a root partition, which in Linux is denoted by a "/".

Click OK once you have finished setting the partition information and you will return to your partition screen, now showing the root partition you just created. Using the same methods as before, create a SWAP partition. 

I recommend you set the size of your SWAP partition to at least the size of your available RAM. If you have plenty of hard disk capacity I would suggest you use double the size. So if you have 2GB of RAM, set it to either 2GB or 4GB. For best performance it is recommended you have your SWAP partition at the beginning or end of your drive.

Once you have done that, you should be looking at something like below.



So to re-cap the above, (in my example) we have the following:

• /dev/sda1 is your Windows partition.
• /dev/sda2 is your new root partition (Windows equiv. of C.
• /dev/sda3 is your SWAP space.

Once you are happy with the changes you have made, click install now and proceed to the next step.

Step 8:
As the installation starts to copy the required files to the hard disk, you will be presented with a screen to select your locale. It should automatically find where you are, as it has for me already:



Just double check it is correct, and then select continue.

Step 9:
The next screen to appear will be keyboard layout:



Ensure the correct option is selected, above you will see the correct (and default UK) selection has been automatically made for me.

Step 10:
You will now be greeted by the "who are you" screen, ready for you to fill out with your user details:




The computers name and username will automatically populate when you type your full name. You can however edit them as you please. Fill in the details and then click continue.

You can opt to have Ubuntu automatically log in for you -- even with a password set -- or you can choose the traditional option requiring a password to log in. You really don't need to choose the encrypt option unless you're installing on a laptop and are dealing with highly secure information.

Step 11:
The installation information screens will now appear as Ubuntu continues the installation:




Step 12:
Once installation has finished, you will be presented with the following box:



Select "restart now" and when requested, remove your installation CD, then press enter to reboot.

Step 13:
For those of you that have Ubuntu as the only OS the computer will boot directly into Linux. If you're dual-booting, you will see the GRUB menu appear similar to below:



Hit enter, to select the first option and load your newly installed Ubuntu OS.

Step 14:
For those that elected to automatically log into Ubuntu, you will go straight to the desktop in Step 15. For everyone else, you will be greeted with the new login manager for Ubuntu:




Enter your password, and hit enter to login to your desktop.

Step 15:
Your desktop should look like this:




Step 16:
Before we proceed further, let's check for updates. Click on the power button on the top right corner of the screen and select "check for updates," or words to that effect.




I'd already run updates on this install so the example above is displaying "software up to date," but the picture highlights where you need to select anyway. 

Upon selecting the update option, the update manager will appear, as below:




If it comes up with no available updates, just select "check" again to verify that it is correct. Having done the same thing myself, I was presented with the updates you see above. For those that opted to install updates during installation it is unlikely there will be further updates required.

You might be asked to enter your password to confirm changes. If prompted, enter your password and click OK. The same is true of any notifications that may appear during updating the OS.

Once complete select close, and restart Ubuntu.The power button is located on the top right corner of the screen. Click this and select shutdown.

Step 17:
No install is complete without full support for mp3s, core MS fonts, DVD playback codecs, Flash and Java, so let'sgo ahead and sort this now.

Click the black Ubuntu menu button at the top left corner of the screen and in the menu that appears, type "software centre" and select the Ubuntu Software Centre. Once open, click the search bar, type "restricted" and the following should appear:




Select Ubuntu restricted extras, and then click on the install button. 

Authentication is much like UAC (user access control) in windows Vista and 7. It is required to elevate your user privileges to that of root (Linux administrator). 

Ubuntu restricted extras will now download, sort any dependencies and install. You can check its progress by viewing the progress bar above the install button. Once finished the In Progress tab will disappear -- restart Linux.It's not strictly necessary, but I always do it after installing this package so everything can start up properly.

Now you can enjoy your new OS and begin exploring its features.

If you have any problems just comment. 

Don't forget to thanks.... :-)

Powered By: http://sunssolution.blogspot.com/